FUE950 SIEMENS PDF

They contain detailed safety regulations, information and specifications which must be observed when installing. The device must be carefully operated and maintained. Only qualified personnel should install or operate this device. Note Sealing The label seal on the calculator must not be damaged! Safety note Note Personnel qualifications - particularly important for mains-powered versions Device installation is only to be performed by personnel qualified to handle electrical devices of at least low voltage up to V. Equipment used in hazardous areas must be Ex-approved and marked accordingly!

Author:Kanris Gardakree
Country:Iceland
Language:English (Spanish)
Genre:Travel
Published (Last):23 March 2014
Pages:354
PDF File Size:19.38 Mb
ePub File Size:11.12 Mb
ISBN:322-2-98543-569-7
Downloads:13642
Price:Free* [*Free Regsitration Required]
Uploader:Mazukinos



Gubei Before removing the inner plastic cover the mains power shall be switched off. The 2 resistors must be mounted between terminals 57 and 58 in the MAG terminal socket. LCD off to save power and returns to basic display menu when button is pressed again. Check cable plug connection of power supply module.

The display menu name is IN0, see menu description Page Proper transport, storage, installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any problems. The display is also switched off, but can be switched on again by pressing any button.

For more details, please contact Siemens Flow Instruments. Page 33 M-Bus-repeater or M-Bus-master. Waste industrial batteries are accepted back by Siemens or by the local Siemens representative. Appendix Appendix Conformity to guidelines Declaration of conformity Siemens hereby declares that this product meets the essential requirements of the following guidelines: Page 11 Before removing the inner plastic cover the mains power shall be switched off.

Functions and settings can be checked via display menus 3 and 4 and freely programmed using a software tool and the IrDA interface. Product information on the internet http: A damaged tue will siemehs in immediate invalidation of the factory warranty and calibration. Sensors in forward and return lines must fit right to bottom of sensor pockets. To print isemens manual completely, please, download it.

RS output Type The optional plug-in RS communication module is a serial interface and permits data exchange with the calculator. The integrator should be installed in a position that makes operation and service easy. The settings and functions for the modules can be changed via a free using software tool and the IrDA interface of the FUE Short press Returns to menu 3.

Tariff energy 2 1. Cue 70 Appendix A. Page 72 Further information www. The board contains 2 terminals marked as 24 and 25, which are typically connected to the M-Bus master M-Bus controlling centre. Functions and settings can be checked via display menu 3 and freely programmed using a software tool and the IrDA interface. Energy calculator is provided with a thread seal or adhesive label seal. Measurement repeatability stated by manufacturer will be obtained if further described environmental conditions are present.

Page 30 The display sieemens also switched off, but can be ziemens on again by pressing any button. Error is used as a warning. Page 42 Tariff energy 2 1. SW-tool Leak detection water meter at Disables: The energy calculator is modular in construction and can be fitted with optional modules depending on the application. Please talk to your local Siemens contact or follow the return procedures of Siemens Flow Instruments described in chapter: Short press Returns to menu 4.

Connect shield to grounding at flowmeter. Return Procedures Fue industrial batteries are accepted back by Siemens or by the local Siemens representative. Comments to this Manuals Your Name. Close lid and check meter for correct operation by pressing push button. The functions and settings of the outputs sidmens be freely programmed using a software tool and the IrDA interface, e. Page 12 Safety notes 2. Enter text from picture: Observe information of temperature sensor installation. Slot 1 to the left is intended for the M-Bus or RS communication modules or the pulse input module.

Page 56 E — 9 Display Battery empty checked Monitors: Wall mounting The device is mounted using the wall bracket supplied ambient temperature: Reference source not found Type label A typical FUE type label shows the following main information: Dimension Drawings Dimension drawings Short press Returns to menu 2.

Ultrasonic flowmeters ip65 nema 7 compact precision volume 7me pages. Figure S — User sealing 3. Related Posts.

HOFMANNSTHAL DER SCHWIERIGE PDF

SIEMENS SITRANS FUE950 มิเตอร์วัดการใช้พลังงานความร้อน/ความเย็น

Mezitaxe Got it, continue to print. Page 30 Ssiemens display is also switched off, but can be switched on again by pressing any button. Display LCD off to save power and returns to basic display menu when button is pressed again. Short press Returns to menu 3. Safety Notes Material compatibility Siemens Flow Instruments can provide assistance with the selection of wetted sensor parts.

LIBRO PSICOGEOMETRIA PDF

SITRANS FUE950

Equipment used in hazardous areas must be Ex-approved and marked accordingly! This device is NOT approved for use in hazardous areas! Lithium batteries may present a potential hazard if they are abused electrically or mechanically. Page 4 2. Prepare cable entries. Connect temperature sensors. Page 5 4.

Related Articles